Apps
About
EN
Buy

Fan control on Apple Silicon: why it seems not to work on M3 and M4

Partly. On M3 and M4 Pro and Max MacBook Pros, fan apps say manual speeds work only after macOS starts the fans; M1 and M2 allow full control.

That’s why a fan app can look broken on a newer MacBook Pro. You drag the slider, the fans stay at 0 RPM, and nothing seems to happen. In most cases the app isn’t broken. The Mac’s firmware is deciding when the fans may run.

First check: does your Mac have a fan?

MacBook Air models with Apple chips have no fan. They cool passively and slow the chip down when they get hot. No app can add or control a fan on them, so a fan control app will only show temperatures on a MacBook Air.

MacBook Pro, Mac mini and Mac Studio models have fans.

Why fans stay off on Apple Silicon

Apple Silicon Macs often keep their fans fully off at light loads. The chip runs cool enough that the fans stop, which is why you may see 0 RPM in any fan app while browsing in Safari or writing in Pages.

Fan app makers describe the limits like this (as of 16 Nov 2026, from their own pages):

Mac What fan apps report
M1 and M2 models with fans Full manual control in Macs Fan Control
M3 and M4 Pro and Max MacBook Pro Manual control only after macOS starts the fans itself, around 77 °C according to CrystalIDEA, the maker of Macs Fan Control. TG Pro describes the same limit.
MacBook Air with Apple chips No fan

CrystalIDEA has a support page on this (“limited fan control on some models”). Apple doesn’t document how its fan firmware decides, and the behavior can change with macOS updates.

What you can do

  1. Check whether the fans are actually needed. Open Activity Monitor (Applications > Utilities), click the CPU tab and sort by % CPU. An app stuck at high CPU heats the Mac more than any fan setting will fix.
  2. Run one fan app at a time. Two apps writing fan speeds fight each other. Quit the other app before you try manual control.
  3. Use a curve or a preset that raises the fans under load. On models with the M3 or M4 limit, a manual speed will usually take hold once macOS has spun the fans up, for example during a render or an export.
  4. Go back to Automatic when you’re done. Automatic hands the fans back to macOS, which is what Apple designed the cooling around.

What MACfan does

MACfan is a fan control and temperature app for Mac: see every sensor and set each fan to a fixed speed or a curve.

  • Set each fan on its own, at a fixed speed in 100 RPM steps, or on a multi-point curve tied to the sensor you pick.
  • When a fan won’t spin, MACfan shows a plain reason in the app, so 0 RPM doesn’t look like a fault.
  • Presets can switch when you plug in the charger, go on battery, or reach quiet hours (up to 8 rules, off until you turn them on).
  • A reading every 5 seconds, kept for 2, 12 or 24 hours, with CSV export and up to eight temperature alerts.
  • It shows when macOS slowed your Mac down because of heat.
  • A macfan command for Terminal, Shortcuts support, and over 40 MCP tools for AI assistants.

The safety rules are built in. Above 100 °C on any sensor, manual control stops and the fans go back to Automatic; heavy loads can trigger this. If MACfan quits or freezes, a watchdog returns the fans to Automatic within seconds. It always opens in Automatic, and a saved manual preset never turns on at launch. Reading sensors needs nothing extra. Changing fan speed needs a small helper that you allow in System Settings.

Honest limits: MACfan has been tested on one Mac so far, an M5 Max with two fans. Intel Macs and other Apple Silicon models, including M3 and M4 MacBook Pros, aren’t confirmed yet, so we can’t promise it gets around the fan limit on those models. Apple doesn’t document its sensors, so names and readings vary by model. MACfan makes no promise of a cooler or longer-lasting Mac; it shows readings and sets the speed you pick. It needs macOS 14 or later.

Questions

Can I control the fans on an M3 or M4 MacBook Pro?

Only partly, according to fan app makers: manual speeds take effect after macOS starts the fans, around 77 °C per CrystalIDEA. Below that, the fans usually stay off whatever the app says.

Why does my Mac’s fan show 0 RPM?

Apple Silicon Macs often stop their fans at light loads because the chip runs cool. 0 RPM at idle is normal and doesn’t mean the fan has failed.

Does the MacBook Air M2 have a fan?

No, MacBook Air models with Apple chips have no fan. A fan app can only show their temperatures.

Is it safe to control Mac fans manually?

It’s safe when the app stays inside hardware limits and hands control back to macOS. MACfan returns the fans to Automatic above 100 °C, when it quits or freezes, and every time it starts.

Does Macs Fan Control work on Apple Silicon?

Yes, with the same limits: full control on M1 and M2 per CrystalIDEA, and limited control on M3 and M4 Pro and Max MacBook Pros.

MACfan is $6, paid once with a year of updates, or $22 for all six Simpel apps. See MACfan.

Your order

Total, paid once

Includes one year of updates. After that you keep the version you have, forever.

Simpel news, and 10% off

Updates, new apps and future offers by email. Confirm your address and we send you a personal 10% code. The code works once checkout opens.

Only Simpel news. Leave any time. Privacy ·